How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
The article author is making a number of good observations on the subject of Installing A Bathtub in general in this article down below.
Mounting a bathtub isn't specifically rocket science, however it does need solid plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a new one is likewise a reasonably hard task. If the old tub is readily easily accessible, the job can relocate speedily; if you have to open a wall to eliminate the old bathtub and also position the new bathtub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Ensure you have certified yourself for the task as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently gotten a new tub and don't require to transform the setup of your previous water pipelines.
Your tools and material checklist should make up the following:
Preparing for the Installment
To start with, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water system. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited accessibility that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the remaining water that will originate from the pipelines. As soon as the supply pipes have been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Before moving on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are useful in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four little points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the outermost versatile faucet port to the suitable supply pipe by making a compression join; then do the very same for the various other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leaks and also tighten them if essential. Load the tub and also check the overflow electrical outlet and also the typical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the tub should wait till the bath tub has actually been used at the very least when as this will settle it into its final placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Protect the tap in position with the maker offered backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous type should be attached to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split a rigid seal, triggering the water to penetrate the wall in between the bathroom and the tiling, causing complications with moisture and also possible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water prior to securing, to allow for the activity experienced when the tub is in usage. The sealant can split rather early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently available on the market. It is a good idea to fit the ceramic tiles making use of waterproof or waterproof glue and cement.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
We were made aware of that report on How to Install a Bathtub through a good friend on a different web blog. Feel free to take the opportunity to distribute this blog entry if you enjoyed reading it. Thank you so much for taking the time to read it.
Book A Service Call
Report this page